Power Panels
Power Panels - Power Control Centre (PCC)
Motor Control Centre Power Panels are used for scattering and control of various power sources used in industry. Commonly Power Control Centre are informed close with drive source along these line issue level is high. It is expected to suit the issue level of 50 KA RMS for 1 sec. Busbar structure in Power Control Centre are planned to suit the Leakage level as well as temperature increment to 40°c above encompassing. Sufficient room is obliged interface end. Various protections obstruct, earth Leakage, under voltage, etc. are given to shielding source and equipment.
- Fixed type fully compartmentalized type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 600V&440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 6000A Busbar (E-91 EC grade Aluminium/Copper).
- The The short circuit fault level is 65KA/50KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
MOTOR CONTROL CENTRE (MCC)
Motor Control Centre are reasonable for the activity of motors going from 0.5 HP to 500 HP limit. Motor control focus contains different kinds of beginning viz. Direct on line (DOL), Star-Delta, auto transformer, soft starter and so forth Neighborhood and distant activity office, viable to PCC/DCS based activity. Motor Control Centre is appropriately ventilated if there should be an occurrence of higher size of engine starter. Part design is made in order to work with simplicity of activity and upkeep.
- Fixed fully compartmentalized type design.
- Single/Double front operation.
- Auto/Manual operation facility through PLC/SCADA & Pushbutton control station.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 4000A Busbar (E-91 EC grade Aluminium/Copper).
- Short circuit fault level is 50 KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
APFC PANELS
Our Power Panels include Automatic Power Factor Control (APFC) is designed to maintain a power factor of plant to unity. To maintain a power factor of unity means to achieve demand in KVA on the lower side. Power factor is maintained to set the value using APFC relay in auto mode where as in case of failure of APFC relay manual push buttons are used. Auto as well as manual mode is provided for power factor control. Various types of capacitors are used depending on load conditions. Typically, MPP, APP or mix dielectric types of capacitors are used. In case of nonlinear loads like VFD, UPS Thyristor switching, suitable detuned reactors are used along with capacitors to filter harmonics.
- Auto/Manual operation facility through APFC Relay & Pushbuttons.
- Proper ventilation with exhaust fans for capacitor banks cooling.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph, 4-wire.
- The The short circuit fault level is 50KA/36KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
SYNCHRONIZING PANELS
DG Synchronising Panels are used to supply DG set power in the absence of main power. It comprises of control of DG set as well as switching of breakers. In absence of main source, it starts DG set automatically, i.e.Auto mains failure (AMF), synchronizes DG set with each other automatically along with auto load sharing and load dependent start/stop of DG set. On resumption of mains, it operates respective breakers and switches off DG set.
- Synchronization functions both manually & automatic synchronizing for two or more gen sets and breakers.
- AMF (Automatic Mains Failure) Operation.
- Load Sharing and Load Dependent Start / Stop for multiple Gensets
- Soft loading & Standby Operation
- Energy Import & Export Control & Programmable operational sequence.
- Fixed type fully compartmentalized type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 4000A Busbar (E-91 EC grade Aluminium/Copper).
- The short circuit fault level is 50KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
POWER DISTRIBUTION BOARDS
Power Distribution Panels are used for distribution of power on down streams. Since it is located at downstream fault level is normally lower about 20 to 35 KA. Normally it is designed to carry current up to 800A. The advantage of using Power Distribution Panel is to clear fault locally, hence it does not affect Upstream Switchgear.
- Floor mounting/wall mounting type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 800A Busbar (E-91 EC grade Aluminium/Copper).
- The short circuit fault level is 50KA/36KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
OUTDOOR PANELS
LT KIOSKS panels are typically standalone protection for the main supply, for ease of control. These can also be designed to provide uninterrupted power from a dual source for wide power distribution across residential layouts.
- Fixed with floor/wall mounted type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 800A Busbar (E-91 EC grade Aluminium/Copper).
- The short circuit fault level is 50KA/36KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
VFD PANELS
AC Drives (Variable Frequency Drives) are used to control speed of motors. Speed control of motor may be a necessity of processor it is done for energy saving. These are used for speed control of pumps, blower, agitator, conveyors, etc. AC Drive panels are properly ventilated to take out the heat generated by VFDs. Proper size choke is provided on input and output size of VFD as required.
- Auto/Manual operation facility through BMS/SCADA & Pushbutton stations.
- Proper ventilation with exhaust fans for cooling.
- Bypass start/stop control facility provide in case the VFD fails.
- It offers smooth operations at starting and stopping and also reduces thermal and mechanical stress on motors.
- Pre-programmed and factory wired VFD’s offers easy way for connection and maintenance
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- The short circuit fault level is 50KA/36KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
AMF Panels
AMF Panels are used for emergency power supply during the main power supply failure. These AMF panels are used for automatic operation of gender as it helps to rotate the starting gear of Genset after main supply is cut.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- The short circuit fault level is 50KA/36KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
FIRE PUMP CONTROL PANELS
The firefighting process is done by pumps designed specifically for the system. Initially the jockey pump is used to maintain the pressure and when the fire is confirmed by a sprinkler or by the fire alarm panel the electric pump starts to work and then in case Failure or disconnection of Electricity for Electric Fire Pump The diesel pump is entered into the process.
- Fixed type with floor/wall mounted type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for the main structure/mounting plates, 16-gauge sheet for doors/covers/partitions and 10-gauge sheet for removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 630A Busbar (E-91 EC grade Aluminium/Copper).
- Short circuit fault level is 36 KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
METER/ACCL PANELS
Meter Panels are used in multi-storied residential or commercial complexes, our low voltage metering cubicles are known for their compact design and ease of control to monitor each load section. Along with meter panels are equipped with the primary change over switches, MCCBs, Earth Fault relays and Fuses to provide multiple fault protection.
Additional Autochanger ACCL switches can be installed to ensure a smooth transition to Diesel Generators during power failure.
- Fixed type with floor/wall mounted type design.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 16-gauge sheet for main structure/doors/covers/partitions & a 14-gauge sheet of removable gland plates.
- Rated voltage is 440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Rated Current is up to 250A Busbar (E-91 EC grade Aluminium/Copper).
- The short circuit fault level is 25KA/10KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
- 1100V grade FRLS multi strand flexible cables for control/power wiring.
BUS-DUCTS AIR INSULATED (SEGREGATED & NON- SEGREGATED)
A key part of electrical power distribution is bus duct. Also called subway, bus duct provides an alternative means of conducting electricity. Bus duct is used in commercial and industrial settings to conduct electricity to power cables or cable bus. Structurally, a bus duct is a sheet metal duct containing either aluminium or copper Busbars (metallic strips or bars that conduct a substantial electrical current) in a grounded metal enclosure. Bus duct is easy to maintain and flexible, helping to accommodate changing load requirements.
- Indoor/Outdoor Installation as per application.
- Dust & Vermin proof enclosure with IP42/IP54/IP65 protection class.
- CRCA 14-gauge sheet for main structure, 16-gauge sheet for doors/covers.
- Rated voltage is 690V/440V, +/- 10%, 50HZ, 3-Ph,4-wire.
- Short circuit fault level is 50 KA for 1sec.
- Non-Hygroscopic SMC/DMC insulators for bus-bar supports.
- Painting type is seven tank process method with 80 microns (min) thickness.
